![]() ![]() TL222 SureGrip™ Silicone Test Lead Set (right to right).CAT IV 600 V CAT III 1000 V, 10 A rating.Multi-purpose tooth pattern grips anything from fine gauge wire to a 20 mm bolt.One pair (red, black) of large alligator clips with nickel-plated steel jaws.Extra hard probe tips to provide long service life.One pair (red, black) of test leads with sharp needle point tips adjustable to desired length from 0 to 76 mm.CAT IV 600 V, CAT III 1000 V, 1 A rating.One pair (red, black) of nickel plated pincers open to 5 mm.Rubber overmolded surfaces and finger-hugging curves give the user a comfortable, reliable grip on the accessory so they can focus on making an accurate measurement. CAT IV 600 V, CAT III 1000 V, 3 A rating.Recommended for use with TL222 and TL224 test leads.Profile narrows to 5.6 mm at tip, hook opening 6.4mm at front, 2 mm at base. ![]() CAT IV 600 V, CAT III 1000 V, 10 A rating.Recommended for use with TL222 and TL224 test leads.Blunt tip grabs round screw heads up to 9.5 mm.One pair of small, insulated, nickel plated jaws. Maximum Voltage: 600Vrms CAT III per IEC 1.Nickel-plated steel jaw contact material with standard jaw opening of 5/16’’ (8 mm). Accepts standard 0.08’’ (2 mm)-pin tip sized test probes. Designed for use with STL 120 and TL75 Test Leads. Includes removable 4 mm lantern tips that thread onto the lead tip Probes always show correct category rating for tip being used Environmental ratings: -20 ☌ to 55 ☌ (-4 ☏ to 131 ☏), altitude: 2000 m (6,562 ft) Conforms to EN61010-031 One-year warranty Ratings: CAT II 1000 V, CAT III 1000 V, CAT IV 600 V, 10 A max., Pollution Degree 2 Exposed probe tip length: 19 mm to 4 mm (0.75 inch to 0.Set of three safety designed insulated Probe Tip Alligator Clips. Universal input plugs are compatible with all instruments that accept standard 4 mm shrouded banana plugs Ratings: CAT II 1000 V, CAT III 1000 V, CAT IV 600 V, 10 A max., Pollution Degree 2 TL175E also available. Extra-heavy duty strain relief on both probe-end and plug-end tested beyond 30,000 bends without failure. TL175 test leads withstand high temperatures and remain flexible in cold temperatures. Each test lead is covered by two layers of silicone insulation inner contrasting color is exposed when the leads are nicked, scuffed, or otherwise damaged and in need of replacement Double insulated silicone leads. TwistGuardTM adjustable tips enhance safety and versatility length WearGuardTM indicator shows damage to leads Heavy-duty strain relief withstands over 30,000 bends Patented TwistGuardTM extendable tip shroud meets the highest electrical safety requirements to reduce tip exposure while providing the versatility needed for most measurements New WearGuardTM lead wire wear indication. Fluke TL175s are the only test leads as tough as your meter. FLUKE TL175 MULTIMETER TEST LEADS FOR 289 287 233 87 83 179 177 175 117 116 115įLUKE TL175 MULTIMETER TEST LEADS FOR 289 287 233 87 83 179 177 175 117 116 115 The Fluke TL175 TwistGuardTM Test Leads offer adjustable length test tips for use in different measurement environments.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |